Kenworth | Commercial Vehicle Protect https://www.cvpnz.co.nz Paint Protection Film (PPF) for commercial vehicles. Sun, 23 Feb 2020 18:38:50 +0000 en-US hourly 1 https://wordpress.org/?v=5.6 Kenworth T410 Custom Fit PPF Film https://www.cvpnz.co.nz/kenworth/kenworth-t410-custom-fit-ppf-film/ https://www.cvpnz.co.nz/kenworth/kenworth-t410-custom-fit-ppf-film/#respond Wed, 05 Feb 2020 04:10:15 +0000 http://www.cvpnz.co.nz/?p=504 The post Kenworth T410 Custom Fit PPF Film appeared first on Commercial Vehicle Protect.

]]>

Custom Fit Application

Kenworth T410 Custom Fit PPF Film

  • Date: February, 2020
  • Client: Southpac Trucks
  • Project Type: PPF Film Application

About this Project

New to NZ, the Kenworth T410 commands a massive presence. With it’s bright colour options and height, this truck will surely be noticed. Built in Australia this T410 has not traveled far to find a home here.

The customer was looking for PPF package which protect the prime areas at the front from stone chipping. 3M SGH12 and Premium Shield Paint Elite Paint Protection Film were used to provide the best levels of protection.

 

  • Remove contaminants from surface for PPF
  • Template on the truck which areas are to be protected
  • Custom fit PPF film to leading front areas excluding chrome bumper
  • Custom fit PPF film to drivers side kick plate

 

Cutting film pattern ready for application
Trimming film on truck - custom fit
Masking up areas for edges
Applying mating solution to film
Top of bonnet after film applied
Positioning PPF film ready for removing excess water
Trimming film edge
Trimming PPF film for edge wrap
Front of truck during PPF application
Cutting pdf film for application
Adjusting film position relative to truck curves
Applying film to headlight area
Wrapping PPF around edges for protection on truck
Contouring PPF to truck curves
Operator trimming film for custom fit to T410 Kenworth
Film resting on contour edge
Removing excess water from under PPF film
Film applied ready for trimming
Cutting film pattern ready for application
Trimming film on truck - custom fit
Masking up areas for edges
Applying mating solution to film
Top of bonnet after film applied
Positioning PPF film ready for removing excess water
Trimming film edge
Trimming PPF film for edge wrap
Front of truck during PPF application
Cutting pdf film for application
Adjusting film position relative to truck curves
Applying film to headlight area
Wrapping PPF around edges for protection on truck
Contouring PPF to truck curves
Operator trimming film for custom fit to T410 Kenworth
Film resting on contour edge
Removing excess water from under PPF film
Film applied ready for trimming
Products of choice for this project were 3MSGH12 and Premium Shield Elite. This film is tough enough to deal with the daily needs of a line haul truck.

The 3M film provides a clear, non-yellowing, fitting with the edges closely matched. While the Premium Shield Elite was used to protect the drivers door entry kick plate.

With many moulded curves, the best choice here was to custom fit. In addition, no templates are available nor likely to be made with soo many uneven surfaces creating waste and the varying options of cover which a client might choose.

Where you are looking to protect commercial equipment, feel free to contact us for a no obligation quote.

Contact Us

Rob

Auckland City | Auckland South

+64 27 230 4914

rob@carpaintprotection.co.nz

Adam

Waikato | Bay Of Plenty

+64 21 2490 292

adam@finaltouch.co.nz

The post Kenworth T410 Custom Fit PPF Film appeared first on Commercial Vehicle Protect.

]]> https://www.cvpnz.co.nz/kenworth/kenworth-t410-custom-fit-ppf-film/feed/ 0